Robe Spot 575 XT Dokumentacja

Przeglądaj online lub pobierz Dokumentacja dla Stroboskopy i światła dyskotekowe Robe Spot 575 XT. Robe Spot 575 XT Specifications Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj

Podsumowanie treści

Strona 2

105. DMX PROTOCOL Mode 1 Mode 2 8bit Value Function Type of control channel channel channel11 1 Pan 0-255 Coarse control of the

Strona 3 - SCAN 575 XT

11Mode 1 Mode 2 8bit Value Function Type of control channel channel channel9 9 7 Frost,cor. filters,3-facet prism 0-95 Open position (hole)

Strona 4 - 1. Safety instructions

126.Controller modeThe fixtures are individually addressed (001-497) on a data link and connected to the controller.The fixturesrespond to the DMX sig

Strona 5 - 2. Operating determinations

13Effect wheelThis wheel has both hot and cold color temperature filters (3200 K and 5600 K). Total numbers of color combinationsare 36. Also wash lig

Strona 6 - 3. Description of the device

147.Stand - alone modeThe fixtures on a data link are not connected to the controller but can execute pre-set programs which can bedifferent for every

Strona 7 - 4.1Fitting the lamp

158. Functions of the control panelThe control panel situated on the front side of the fixture offers several features. You can simply set the DMXaddr

Strona 8 - 4.5 Connection to the mains

16If message "MASt." fast flashes-DMX signal is received at the DMX-input- disconnect DMX controller!Only one fixture may be the master. Up

Strona 9 - Controller operation

17- The number of the hours that the SCAN 575 XT has been powered On since thecounter was last reset.Press [Enter] or [Mode] to return to the menu.I

Strona 10 - 5. DMX PROTOCOL

18Software versionBy this function you can read the software version of the display module. Press [Enter] to read its value or[Mode] to return to t

Strona 11

1910 Prism rotation control Prism rotation control Rot.gobo rotation11 Rotating gobos Rotating gobos Iris12 Rot.gobo rotation Rot.gobo rotation Focus,

Strona 13 - Dimmer / Shutter / Strobe

20confirm or [Mode] to cancel and return to the menu.Important: The option"Off" is for "emergency operation" only if the lamp ligh

Strona 14 - 7.Stand - alone mode

21temperature inside increases about certain level (the low fan speed reduces the cooling of thelighting). This cycle can repeat several times until t

Strona 15 - 8.1 Addressing

228.5 Switching On/Off the lampPress the [Mode] button in order to access the main menu. Browse through the menu by pressing the [Up] and[Down] button

Strona 16 - 8.2 Slave control

23Presetting playbackThis function allows you to select the the program which will be played in the stand-alone mode after switchingthe fixture On.Us

Strona 17 - DMX values

24"dimr" - a dimmer, value 0-255"S.tim." - a step time,value 0,1-25,5 seconds"COPY." - a copying the current prog. step

Strona 18 - 8.4 Personality options

25Lamp adjustmentThis function can be used when you make the fine adjustment of the lamp.If you select "LAAd" pressing by[Enter]-button ,all

Strona 19

26Now you can calibrate the the colour, gobo and effect wheels by your controller. The DMX calibration protocol isdescribed in the table.DMX Calibra

Strona 20

27caused by the lamp.Caution: The message is disabled if the lamp light sensor (function "En.Sn.") is switched Off.FAnThe message informs yo

Strona 21 - Default settings

2810. Technical specificationsPower supply:EU version -Voltage...208/230/240V AC, 50/60 Hz ~-Fuse...

Strona 22 - 8.7 Stand-alone setting

29Beampath:Electronics:-Addressing, special functions setting, effects calibration via control panel with 4-digit LED display-Readout fixture and lamp

Strona 23 - Editing program

3Table of contents1. Safety instructions... 42.

Strona 24 - 8.9 Special functions

30Housing- Easy access to lamp and main components thanks to large opening cover and the projector‘smodular construction.Dimensions (mm):Weight:22 kgA

Strona 25 - Fixture code

3112. Appendix12.1 Changing the power supply settingsBoth the transformer and the ballast must be connected correctly for the local AC voltage and fre

Strona 26 - DMX Calibration protocol:

4CAUTION!Keep this device away from rain and moisture!Unplug mains lead before opening the housing!FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL C

Strona 27

52. Operating determinationsThis device was designed for indoor use only.If the device has been exposed to drastic temperature fluctuation (e.g. afte

Strona 28 - 10. Technical specifications

63. Description of the device1 - Fastening screws2 - Fixation screw for bracket3 - Bracket4 - Objective5 - MirrorFront panel:6 - DMX Output7 - DMX Inp

Strona 29 - Minimum distances:

74. Installation4.1Fitting the lampDANGER !Install the lamps with the device switched off only.Unplug from mains before !To insert the lamp (Osram HMI

Strona 30 - 11. Maintenance and cleaning

84.4 Rigging the fixtureDanger of fire !When installing the device, make sure there is no highly inflammablematerial (decoration articles, etc.) in be

Strona 31 - 12. Appendix

9The occupation of the connection-cables is as follows:Cable (EU) Cable (US) Pin InternationalBrown Black Live LLight blue

Komentarze do niniejszej Instrukcji

Brak uwag